Berkeley CSUA MOTD:Entry 23569
Berkeley CSUA MOTD
 
WIKI | FAQ | Tech FAQ
http://csua.com/feed/
2025/07/08 [General] UID:1000 Activity:popular
7/8     

2002/1/15-16 [Computer/Networking] UID:23569 Activity:high
1/15    How can I setup my router so that it will take in both my AT&T AtHome
        IP and my internal corporate DSL (intranet)? Do I need a switch or
        a bridge of some sort?                          -network clueless
        \_ thats a pretty complex networking problem.  You need a router
           machine( could be a Linux or other opensource OS system) with 3
           ether ports to take the traffice and sort out the routing.  Then
           you need to set it up with NAT or somesuch to translate things
           so that the single 'inside' ip address you use at home gets
           translated right so traffic to your corporate DSL thinks you're
           inside it for traffic going to corporate networks, and then
           dumps the rest of the traffic out your at hom3 connection. -ERic
                \_ and you have to be careful not to tell anyone at work
                   about it because you'll get your ass fired for exposing
                   the corporate network to the world.  -tom
                   \_ if they cared then no-clue lad wouldn't have dsl direct
                      to the inside of the corp net anyway.
2025/07/08 [General] UID:1000 Activity:popular
7/8     

You may also be interested in these entries...
2007/4/19-21 [Computer/Networking] UID:46375 Activity:nil
4/19    After installing Logitech wireless mouse, my friend cannot connect from
        his PC to his wireless broadband router via a USB wireless network
        device.  It said that it cannot obtain IP address from the router.  Even
        uninstalling the Logitech wireless mouse doesn't help.  Do you know how
        to fix the wireless LAN problem, so that his PC can obtain IP address
        again?
	...
2006/3/25-27 [Computer/Networking] UID:42433 Activity:nil
3/24    I want to write in my DSL router to allow incoming connection
        from certain IP range. How do I find out the IP range for SBC
        DSL say in Bay Area/SF?
	...
2006/2/18-23 [Computer/Networking] UID:41923 Activity:low
2/18    My DSL modem's ip address is 192.168.0.1, my internal network
        behind my router is 10.0.0.x. Is there a way I can configure
        the router so I can access the DSL modem from my 10.0.0.x
        network directly without re-wiring? Static routes? I tried it
        but no much luck. I also tried changing my internal network to
        192.168.0.x, but still does not work. Thanks.
	...
2006/1/28-31 [Computer/Networking] UID:41585 Activity:low
1/28    Just switched to Comcast from SBC and generally happy with it.  But
        can someone please explain to me why they are constantly pumping
        ARP traffic through the network?  It seems harmless, but I'm curious
        as I didn't see it with DSL.  It's a little disconcerting to see
        constant traffic on your router, even if ARPs are harmless from
        a bandwidth perspective, and it makes the WAN send/receive light
	...
2006/1/22-24 [Computer/Networking] UID:41477 Activity:nil
1/21    I am trying to setup a small network for my girlfriend's
        mom's company.  They just bought an accounting package
        which requires windows 2003 server.  And they want internet
        access from each computer.  How should the network be setuped?
        Would it be dumb to use static IP for each computer and a
        computer as internet gateway?
	...
2005/8/29-30 [Computer/Networking] UID:39329 Activity:moderate 54%like:37400
8/29    What's the difference between a hub, a switch and a router?  Thx.
        \_ AFAIK, probably be corrected by someone:
           hub: Allows communication on a LAN with bandwith shared amongs all
                the nodes on the hub and maxing out at the max line speed.
           switch: Allows communication on a LAN with bandwith greater than
                the max line speed (point to point)
	...
2005/6/2-3 [Computer/Networking] UID:37941 Activity:moderate
6/2     I've been to many places and almost every place I go to have
        802.11b/g. However, almost all of them have protected access,
        which I presume they use because they don't want people stealing
        their bandwidth. So here is one idea I think will really
        revolutionize 802.11X... an option in the router that allows you to
        specify the percentage of unprotected bandwidth you are willing to
	...
2005/2/25-27 [Computer/Networking] UID:36421 Activity:moderate
2/25    What is the smallest (physical and price) cisco router that can
        handle BGP?  It should be able to have more than 256 ram.
        \_ When you say ``handle BGP'', do you mean supports the bgp
           protocol or supports enough ram to keep a reasonable (what do you
           consider to be reasonable) number of routes in memory?  Do you want
           to be peering at PAIX, or do you just need a router to run the T1
	...
2005/1/13-14 [Computer/Networking] UID:35697 Activity:high
1/13    I need help fixing someone's Win2K box.  Setup:  Win2K box -> D-Link
        router -> DSL modem.  The Win2K box cannot obtain a DHCP address
        (other computers can).  So, I assign a static IP, and set the default
        gateway and DNS server to be the D-Link router.  After this, the Win2K
        box can access web pages on the Internet as long as you specify the
        web site IP address directly -- but DNS doesn't work.  Computer used
	...
2005/1/10-11 [Computer/SW/OS/VM] UID:35635 Activity:kinda low
1/10    VMware question for VMware gurus only. I've installed a WinXPsp1
        on top of WinXPsp2. How do you do the followings:
        1) transfer data between the two machines? I've tried mounting
           raw partition from WinXPsp1 but when I disable write, it
           doesn't boot up anymore (WinXP insists on writing)
        2) communicate between the two machines? I can ping WinXPsp1
	...
2004/8/24 [Computer/Networking] UID:33119 Activity:nil
8/24    To those with Cisco/router fu:
        My co-worker walked over and asked me what the "set default interface"
        command does if you don't specify a next-hop IP address.  I said
        you always need a next-hop IP address, unless you expect the
        destination IP address in the IP header to be on the directly connected
        network.  He said it will broadcast on that interface.  I'm googling
	...
2004/4/7-8 [Computer/Networking, Computer/SW/OS/OsX] UID:13077 Activity:nil
4/7     What startup script or configuration file can be modified to set
        the ip address of a unix (actually Mac OS X) box to a particular
        value?  This is an emergency.  Thanks a lot in advance!
        \_ you can try running ifconfig or ipconfig *after* startup.
           http://www.macosxhints.com/article.php?story=20020415091242448
           \_ Tnx.  But is there a way to directly set the manual ip addr
	...